MOUNTING - Instructions and important information
Before installation, compare the parts certificate, the part type approval or the ABE with your vehicle documents to ensure that this SCC product has been tested and approved for your vehicle and that your wheel/tyre combination is listed.
Please make sure to observe the product- and vehicle-specific requirements for your wheel spacers or adapter plates. You can find these on our website www.spurverbreiterung.de. To access them, navigate through the categories "Wheel spacers search by Vehicle" or "Adaptation search by Vehicle", select your vehicle, and open the "Requirements" tab on the product page.
1. Secure vehicle against rolling away
2. & 3. Loosen wheel bolts and position the jack
Before removing the wheel, the wheel fastening elements – wheel bolts or wheel nuts, depending on the vehicle – must generally be loosened while the vehicle is standing on the ground and the wheel is still under load, since only the vehicle’s own weight prevents the wheel hub from turning with the fastener and ensures the fastening elements can be loosened safely.
Then position the jack at the designated body points and slightly relieve the load on the wheel (3). Alternatively, a lifting platform can be used to safely raise the vehicle.
4. Raise the vehicle and secure it with a jack stand
5. & 6. Remove wheel fastening elements and take off the wheel
7. Clean the contact surface
Contamination, corrosion residue and old paste residue on the contact surface of the wheel hub must be completely removed before installation, as these deposits prevent the wheel spacer from sitting flush and parallel. Uneven contact causes the bolted connection to yield and settle under operating load, meaning the required tightening torque cannot be maintained permanently. In the worst case, this results in a safety-critical loss of clamping force, up to and including the wheel coming loose while driving.
8. Check the outer chamfer
9. Position the wheel spacer – IMPORTANT NOTES!
10. Apply corrosion protection paste
With alloy wheels and wheel spacers, two critical contact areas are created where galvanic corrosion can occur due to moisture and road salt – aluminum-on-aluminum connections in particular tend to cold-weld. A thin layer of assembly paste should therefore be applied to all centering surfaces. The contact surfaces – i.e. the surfaces on which the wheel spacer and rim sit flush against each other – must, however, remain completely free of paste, as it acts as a lubricant, distorts the tightening torque of the bolts and reduces the clamping force, which in the worst case can cause the wheel to come loose.
11. Check fastening elements
Ball seated
Ball Taper Radii
Tapered 60°
Minimum screw-in depth of fastening elements
| Thread | Thread reach | Min. rotations |
|---|---|---|
| M12 x 1.25 | 10 mm | 8.0 |
| M12 x 1.5 | 10 mm | 6.5 |
| M12 x 1.75 | 12 mm | 6.5 |
| M14 x 1.25 | 12 mm | 9.0 |
| M14 x 1.5 | 11 mm | 7.5 |
| M14 x 2.0 | 14 mm | 7.0 |
| M15 x 1.25 | 10 mm | 8.0 |
| 1/2" UNF | 11 mm | 8.0 |
Tightening torques
12. Fit the wheel spacer
Advice for System 5
Advice for System 3
IMPORTANT NOTE!
Please note that when using our System 3 with spacer thicknesses of up to 25 mm, the vehicle’s original studs and/or fastening nuts will generally protrude. This depends on the specific design of the wheel hub and the length of the original studs.
Fitting the rim onto the wheel spacer is only possible if the rim used has corresponding *cast or milled pockets on its rear side, between the fastening holes, which can accommodate the protruding bolts and nuts.
If the rim lacks such pockets and the vehicle’s original studs protrude from the wheel spacer, the rim will not sit flush against the wheel spacer, but instead rest on the ends of the bolts or nuts. This leads to imbalance and vibration due to inadequate wheel centering, and in the worst case, to broken studs!
Advice for System 4
Additionally, ensure that the protruding length of the OEM wheel bolts is fully threaded. If not, they must be replaced with bolts that have a continuous thread.
Advice for System 2D and 4D
12A and 12B - System 3 and 4
13. Install the wheel
14. Lower the vehicle
15. Set the torque wrench
Tightening Torque & Preload Force
In bolted connections – especially in safety-relevant applications such as wheel bolts/wheel nuts (hereinafter referred to as „wheel fastening parts“) – the tightening torque is not actually the target value itself. Rather, it serves as an indirect auxiliary value used to reliably build up the required preload force in the connection.
The preload force is the force that the bolt absorbs within itself as it is tightened, and which clamps the components firmly together. Only this preload force ensures that the connection can absorb forces, does not come loose, and reliably transmits shear or transverse loads.
Since the preload force can only be measured indirectly, torque is used in practice as an approximate value. However, this relationship depends heavily on the friction values at the thread and contact surface. Even small differences in lubrication, surface condition or corrosion can significantly change the preload force actually achieved – even though the same torque was applied.
fSM = Elongation of the bolt caused by the assembly preload force
fPM = elastic change in length of the clamped parts caused by the assembly preload force
FM = assembly preload force
16. Tighten the fastening elements
After 100 km, retighten the fastening elements of the wheel spacers. After a further 100 km, retighten the fastening elements of the wheels (Systems 3 and 4). For Systems 2 and 5, retighten the fastening elements of the wheels after 100 km.
Retightening Wheel Fastening Parts
Why retighten wheel fastening parts?
Settling effects in the friction pairing
After assembly, the contact surfaces of the rim, wheel hub and bolt head or nut „bed in“ under load. Surface roughness peaks are plastically deformed, and minor irregularities settle. This reduces the initial preload force in the wheel bolts or nuts. Retightening after 50–100 km restores the required preload force.
Compression of coatings and intermediate layers
Rims are often painted, powder-coated or treated with corrosion protection coatings. Centering rings or thin intermediate layers may also be present. Under wheel load and the micro-movements that occur while driving, these soft layers are compressed or partially sheared. The connection continues to „settle“, causing the contact pressure to decrease. Retightening compensates for this loss.
Effects of temperature and operating loads
While driving, changing temperatures (from braking, ambient conditions) and dynamic wheel loads act on the connection. Differing thermal expansion of the hub, rim and bolt, as well as micro-movements during driving, can further affect the preload force. Controlled retightening after the initial operating cycles ensures that, after this settling phase, the connection once again operates at the intended force level.
Safeguarding against variation during assembly
In practice, the tightening torque is always subject to a certain amount of variation (different tools, differing friction conditions, human factors). The first retightening after 50–100 km therefore also serves as an additional safety measure: it compensates for assembly and measurement inaccuracies and ensures that all wheel bolts or nuts are actually within the intended preload force range, and that the connection cannot come loose unnoticed.
When should wheel fastening parts be retightened?
After every wheel installation – for example after a tire change or the installation of wheel spacers – the connection should be checked and retightened again after a distance of around 50–100 km, as it can still change during this early operating phase due to settling and adjustment processes. Retightening is also recommended after work on the suspension or wheel hub.
For correct retightening, the vehicle should be standing on a level surface. Retightening must only be carried out using a suitable, calibrated torque wrench – an impact wrench is unsuitable, as it does not apply torque in a controlled manner. The manufacturer’s specified torque must be observed. To achieve even contact pressure on the rim, retighten in a crosswise pattern.
No lubrication may be applied to the threads or contact surfaces of wheel bolts and wheel nuts under any circumstances, as any change in friction behavior significantly affects the relationship between the applied torque and the preload force actually generated.
Bolts advice
Ball seated
Ball Taper Radii
Tapered 60°
Minimum screw-in depth of fastening elements
| Thread | Thread reach | Min. rotations |
|---|---|---|
| M12 x 1.25 | 10 mm | 8.0 |
| M12 x 1.5 | 10 mm | 6.5 |
| M12 x 1.75 | 12 mm | 6.5 |
| M14 x 1.25 | 12 mm | 9.0 |
| M14 x 1.5 | 11 mm | 7.5 |
| M14 x 2.0 | 14 mm | 7.0 |
| M15 x 1.25 | 10 mm | 8.0 |
| 1/2" UNF | 11 mm | 8.0 |
Tightening torques
Bolted Connections / Strength
Tightening Torque & Preload Force
In bolted connections – especially in safety-relevant applications such as wheel bolts/wheel nuts (hereinafter referred to as „wheel fastening parts“) – the tightening torque is not actually the target value itself. Rather, it serves as an indirect auxiliary value used to reliably build up the required preload force in the connection.
The preload force is the force that the bolt absorbs within itself as it is tightened, and which clamps the components firmly together. Only this preload force ensures that the connection can absorb forces, does not come loose, and reliably transmits shear or transverse loads.
Since the preload force can only be measured indirectly, torque is used in practice as an approximate value. However, this relationship depends heavily on the friction values at the thread and contact surface. Even small differences in lubrication, surface condition or corrosion can significantly change the preload force actually achieved – even though the same torque was applied.
The Shape of the Seat
The head shape of wheel fastening parts – typically a tapered seat or ball seat (note: different ball radii exist!) – is critical for safe force transmission between the rim and the wheel hub. The shape of the seat determines the contact area through which the wheel fastening part centers itself in the rim and evenly introduces the preload force into the contact surface. If the wrong head shape is used (e.g. tapered-seat bolts in a rim that requires a ball seat), point loads occur that can lead to material deformation, loosening of the connection, or even breakage of the wheel fastening parts or the rim. Only the head shape that correctly matches the rim ensures a form-fit and force-fit connection.
Retightening Wheel Fastening Parts
Why retighten wheel fastening parts?
Settling effects in the friction pairing
After assembly, the contact surfaces of the rim, wheel hub and bolt head or nut „bed in“ under load. Surface roughness peaks are plastically deformed, and minor irregularities settle. This reduces the initial preload force in the wheel bolts or nuts. Retightening after 50–100 km restores the required preload force.
Compression of coatings and intermediate layers
Rims are often painted, powder-coated or treated with corrosion protection coatings. Centering rings or thin intermediate layers may also be present. Under wheel load and the micro-movements that occur while driving, these soft layers are compressed or partially sheared. The connection continues to „settle“, causing the contact pressure to decrease. Retightening compensates for this loss.
Effects of temperature and operating loads
While driving, changing temperatures (from braking, ambient conditions) and dynamic wheel loads act on the connection. Differing thermal expansion of the hub, rim and bolt, as well as micro-movements during driving, can further affect the preload force. Controlled retightening after the initial operating cycles ensures that, after this settling phase, the connection once again operates at the intended force level.
Safeguarding against variation during assembly
In practice, the tightening torque is always subject to a certain amount of variation (different tools, differing friction conditions, human factors). The first retightening after 50–100 km therefore also serves as an additional safety measure: it compensates for assembly and measurement inaccuracies and ensures that all wheel bolts or nuts are actually within the intended preload force range, and that the connection cannot come loose unnoticed.
When should wheel fastening parts be retightened?
After every wheel installation – for example after a tire change or the installation of wheel spacers – the connection should be checked and retightened again after a distance of around 50–100 km, as it can still change during this early operating phase due to settling and adjustment processes. Retightening is also recommended after work on the suspension or wheel hub.
For correct retightening, the vehicle should be standing on a level surface. Retightening must only be carried out using a suitable, calibrated torque wrench – an impact wrench is unsuitable, as it does not apply torque in a controlled manner. The manufacturer’s specified torque must be observed. To achieve even contact pressure on the rim, retighten in a crosswise pattern.
No lubrication may be applied to the threads or contact surfaces of wheel bolts and wheel nuts under any circumstances, as any change in friction behavior significantly affects the relationship between the applied torque and the preload force actually generated.
Replacing Wheel Fastening Parts
Why replace wheel fastening parts?
Material fatigue
With every installation, wheel bolts and wheel nuts are subject to both elastic and, depending on friction conditions, potentially plastic stress. As the number of installation cycles increases, the components age at a material level: the surface coating wears down, the thread wears, and the friction values change. This reduces the repeatability of the tightening torque. Material fatigue is particularly critical: repeated load cycles create micro-cracks that reduce fatigue strength over the long term and, in extreme cases, can lead to failure of the connection. Regular replacement ensures that the wheel fastening always provides the necessary preload force and, with it, operational safety.
Corrosion
Corrosion significantly alters the friction conditions between the thread and the contact surface. Rust creates rougher, uneven surfaces, causing the majority of the applied tightening torque to be „lost“ to increased friction. The result: despite an identical torque, the required preload force is no longer achieved. For this reason, the condition of the wheel fastening parts must be checked regularly, and they must be replaced early at the first signs of corrosion.
Wear and Corrosion
When should wheel bolts be replaced?
Wheel bolts are exposed to strong temperature fluctuations during braking and are therefore subject to natural wear. For this reason, they must be replaced every 2 years!
If corrosion is visible, replace the wheel bolts immediately if possible.
If the wheel is changed multiple times, new wheel bolts are also required. The clamping force of the wheel bolts decreases continuously with every change!
Wheel bolts should be tightened in the correct sequence: crosswise and in several stages. If the bolts are tightened one after another in order, there will be no even contact pressure on the hub and the wheel will sit at an angle. This prevents a clean, true rotation and the wheel bolt can break.
Preventing corrosion
To prevent later wear, wheel bolts or wheel nuts should be checked for damage whenever they are changed. The bolted connections should show no rust or dirt.
Only the strength class specified by the manufacturer may ever be used – otherwise, even the smallest load can quickly lead to wear or breakage.
Product- and Vehicle-Specific Requirements
- Not suitable for use with all vehicles or rims, as the low spacer thickness may mean the spacer does not sit flush against the hub or in the rim! Please observe the centering collar height (ZBH), hub bore depth (NLT), and chamfer values of the spacer and rim (PHO).
- Can only be fitted to vehicles with a centering collar height (ZBH) of the vehicle hub of max. 15 mm.
- Can only be fitted to rims with a chamfer (PHO) greater than 6 mm.
- Please be sure to observe the enclosed mounting instructions.
- Before installation, please check that the supplied wheel bolts match your original bolts (thread & head shape). The length of the supplied wheel bolts must be greater than that of the original bolts by approximately the thickness of the wheel spacer.
- During installation, please check that the new or extended wheel bolts meet the minimum screw-in depth or the minimum number of thread rotations as specified in the mounting instructions.
- During and after installation, make sure that the wheel bolts do not touch anywhere and that the wheel can turn freely.
- Before purchasing, please check whether your vehicle, including power output range and EC number, is included in the TTG/ABE. In addition, please check whether your wheel/tyre combination is included, and observe the applicable requirements, including with regard to any possible inspection/approval.
- Cannot be fitted in combination with steel rims.