EN MOUNTING - Instructions and important information
Please read these instructions carefully and attentively before starting work and follow the instructions contained therein. Failure to do so may result in serious personal injury and damage to property. Steel wheels may only be fitted if the wheel contact surface is completely flat. Incorrect fitting of wheel spacers and wheels can lead to considerable personal injury and damage to property. Only use wheel spacers and fastening elements in perfect, unaltered condition. No persons may be in the vehicle during installation. Installation should be carried out by trained professionals. A suitable installation site and the appropriate specialised tools must be used. The use of an impact wrench is prohibited.

Before installation, compare the parts certificate, the part type approval or the ABE with your vehicle documents to ensure that this SCC product has been tested and approved for your vehicle and that your wheel/tyre combination is listed.

Please make sure to observe the product- and vehicle-specific requirements for your wheel spacers or adapter plates. You can find these on our website www.spurverbreiterung.de. To access them, navigate through the categories "Wheel spacers search by Vehicle" or "Adaptation search by Vehicle", select your vehicle, and open the "Requirements" tab on the product page.
 
! IMPORTANT NOTES! Note
Check that the spacer is completely in contact with the hub mounting surface of the rim.
Check whether the spacer sits fully flush against the axle.
Protruding or excessively long fasteners can cause significant personal injury and property damage.
Pay particular attention to the minimum number of thread rotation of the fastening elements.
Check spacers and fastenings elements at least once a year. Corroded or damaged parts must be replaced immediately.
The use of aggressive cleaning fluids can cause corrosion and thus impair or weaken the fastening material.
1. Secure vehicle against rolling away
Secure vehicle
1
Secure the vehicle by engaging the parking brake and, if necessary, using a wheel chock to prevent it from rolling.
2. & 3. Loosen wheel bolts and position the jack
Loosen wheel bolts
2
Position the jack
3
Loosen the wheel fastening elements (2).

Before removing the wheel, the wheel fastening elements – wheel bolts or wheel nuts, depending on the vehicle – must generally be loosened while the vehicle is standing on the ground and the wheel is still under load, since only the vehicle’s own weight prevents the wheel hub from turning with the fastener and ensures the fastening elements can be loosened safely.

Then position the jack at the designated body points and slightly relieve the load on the wheel (3). Alternatively, a lifting platform can be used to safely raise the vehicle.
4. Raise the vehicle and secure it with a jack stand
Raise the vehicle
4
Continue lifting the vehicle and secure it with a jack stand.
5. & 6. Remove wheel fastening elements and take off the wheel
Remove wheel fastening elements
5
Remove the wheel
6
Remove the fixing nuts/bolts (5) and remove the wheel (6).
7. Clean the contact surface
Clean the contact surface
7
Carefully clean the contact surface and center bore of the vehicle using a wire brush to remove dirt and rust.

Contamination, corrosion residue and old paste residue on the contact surface of the wheel hub must be completely removed before installation, as these deposits prevent the wheel spacer from sitting flush and parallel. Uneven contact causes the bolted connection to yield and settle under operating load, meaning the required tightening torque cannot be maintained permanently. In the worst case, this results in a safety-critical loss of clamping force, up to and including the wheel coming loose while driving.
8. Check the outer chamfer
Check the outer chamfer
8
Check whether the outer chamfer and centering collar of the wheel spacer fit snugly against the inner chamfer of the hub bore and sit flush against the contact surface of your rim.
9. Position the wheel spacer – IMPORTANT NOTES!
Position the wheel spacer
9
!
Place the wheel spacer on the vehicle’s center bore and check that it sits flush and free of play against the inner chamfer and the centering surface on the axle mounting area.
IMPORTANT!
1. Vehicle side
Incorrect!
The depth of the center bore (NLT) in the spacer is smaller than the height of the vehicle hub (ZBH)
Result: Sheared centering collar
A sheared centering collar occurs when fitting the wheel spacer if the vehicle hub (ZBH) is longer than the hub bore depth (NLT) of the spacer
Correct
Always check, therefore, that the wheel spacer sits flush against the contact surface!
2. Rim side
Incorrect!
If the chamfer (PHO) in the rim is smaller than the chamfer (PHO) on the centering collar of the wheel spacer, the rim will sit at an angle on the wheel spacer when the wheel bolts are tightened. In this case too, the centering collar of the wheel spacer will shear off when the wheel is tightened.
Correct
Always check, therefore, that the wheel spacer sits flush against your rim!
10. Apply corrosion protection paste
Apply corrosion protection paste
10
Apply a thin layer of corrosion protection paste to the center bore area of the vehicle. 

With alloy wheels and wheel spacers, two critical contact areas are created where galvanic corrosion can occur due to moisture and road salt – aluminum-on-aluminum connections in particular tend to cold-weld. A thin layer of assembly paste should therefore be applied to all centering surfaces. The contact surfaces – i.e. the surfaces on which the wheel spacer and rim sit flush against each other – must, however, remain completely free of paste, as it acts as a lubricant, distorts the tightening torque of the bolts and reduces the clamping force, which in the worst case can cause the wheel to come loose.
11. Check fastening elements
Check fastening elements
11
Check if the length and type of the new fastening elements are correct (see bolts advice in this installation manual). For wheel bolts, the shaft length must be longer by the thickness of the wheel spacer compared to the original wheel bolts. For wheel nuts, the minimum thread engagement depth specific to the thread must still be maintained (see bolts advice). You may have to order new nuts/bolts separately.
Periodical Check
Check spacers and fixing elements at least once a year. Corroded or damaged parts must be replaced immediately.

Ball seated

Ball seated bolt
Ball Taper Radii

Tapered 60°

Tapered seat bolt

Minimum screw-in depth of fastening elements

Thread Thread reach Min. rotations
M12 x 1.25 10 mm 8.0
M12 x 1.5 10 mm 6.5
M12 x 1.75 12 mm 6.5
M14 x 1.25 12 mm 9.0
M14 x 1.5 11 mm 7.5
M14 x 2.0 14 mm 7.0
M15 x 1.25 10 mm 8.0
1/2" UNF 11 mm 8.0

Tightening torques

Consider the torque which is recommended by the vehicle and rim manufacturer for all fixing elements of spacers and wheels.
Excessive screw-in depth can lead to damage to the axles (brake parts, ABS control discs, etc.). For this reason, after fitting, the wheels should be turned by hand while still unloaded in order to check the inward clearance of the longer wheel bolts. On some vehicles, the critical tolerance is 2 mm!
12. Fit the wheel spacer
Fit the wheel spacer
12
Place the wheel spacer onto the wheel hub and apply a thin layer of corrosion protection paste to the centering collar.
NoteAdvice for System 5
System 5 does not have a hub-centric centering on the wheel side, so the centering remains on the vehicle’s wheel hub. Therefore, the vehicle’s wheel hub must be sufficiently long. After placing the System 5 wheel spacer, the remaining length of the wheel hub must be at least the height of the inner chamfer of the wheel bore plus an additional 3 mm.
NoteAdvice for System 3
After installing the wheel spacers, check whether the supplied nuts and/or the original wheel studs protrude from the spacer. If this is the case, only wheels with appropriate recesses or casting pockets may be used. These recesses or casting pockets must be deep and large enough to fully accommodate the protruding nuts or studs. If not, the original wheel studs may need to be shortened. Failure to comply may result in the breakage of the wheel fastening elements (wheel studs), potentially leading to wheel detachment.
overlapping stud
Overlapping stud
further steps like 12A, 12B and 13 to 16

IMPORTANT NOTE!
Please note that when using our System 3 with spacer thicknesses of up to 25 mm, the vehicle’s original studs and/or fastening nuts will generally protrude. This depends on the specific design of the wheel hub and the length of the original studs.

Fitting the rim onto the wheel spacer is only possible if the rim used has corresponding *cast or milled pockets on its rear side, between the fastening holes, which can accommodate the protruding bolts and nuts.
If the rim lacks such pockets and the vehicle’s original studs protrude from the wheel spacer, the rim will not sit flush against the wheel spacer, but instead rest on the ends of the bolts or nuts. This leads to imbalance and vibration due to inadequate wheel centering, and in the worst case, to broken studs!

NoteAdvice for System 4
 
Warning Personal and material damage can be caused by overlapping or too long fastening elements.
System 4 check
!
Insert the OEM wheel bolt into the wheel and measure the length that protrudes from the wheel. This length must be shorter than the thickness of the wheel spacer. Otherwise, the OEM wheel bolt must be shortened or replaced with a suitable bolt.

Additionally, ensure that the protruding length of the OEM wheel bolts is fully threaded. If not, they must be replaced with bolts that have a continuous thread.
NoteAdvice for System 2D and 4D
Please note that for System 2D and 4D, the original grease cap must be removed before installing the wheel spacers.
12A and 12B - System 3 and 4
Fit the wheel spacer
12A
Install the wheel spacer onto the wheel hub using the supplied fastening elements and tighten them lightly by hand.
Tighten crosswise
12B
Tighten the fastening elements in at least two stages in a crisscross pattern. Only use the supplied fastening elements. Set the torque wrench to the correct value. Refer to the specifications of the vehicle or wheel manufacturer.
13. Install the wheel
Position the wheel
13
Position the wheel and install the original fastening elements by hand. Tighten them lightly by hand.
14. Lower the vehicle
Remove the jack stand
14
Remove the jack stand and slowly lower the vehicle using the jack.
15. Set the torque wrench
Set the torque wrench
15
Set the torque wrench to the correct value. Refer to the specifications of the vehicle or wheel manufacturer.

Tightening Torque & Preload Force

In bolted connections – especially in safety-relevant applications such as wheel bolts/wheel nuts (hereinafter referred to as „wheel fastening parts“) – the tightening torque is not actually the target value itself. Rather, it serves as an indirect auxiliary value used to reliably build up the required preload force in the connection.

The preload force is the force that the bolt absorbs within itself as it is tightened, and which clamps the components firmly together. Only this preload force ensures that the connection can absorb forces, does not come loose, and reliably transmits shear or transverse loads.

Since the preload force can only be measured indirectly, torque is used in practice as an approximate value. However, this relationship depends heavily on the friction values at the thread and contact surface. Even small differences in lubrication, surface condition or corrosion can significantly change the preload force actually achieved – even though the same torque was applied.

Diagram of tightening torque and preload force

fSM = Elongation of the bolt caused by the assembly preload force

fPM = elastic change in length of the clamped parts caused by the assembly preload force

FM = assembly preload force

16. Tighten the fastening elements
Final wheel fastening
16
Tighten the fastening elements in at least two stages in a crisscross pattern. Check twice to ensure that the torque is correctly set.
The wheel spacers and wheels are now properly installed on the vehicle.
After 100 km, retighten the fastening elements of the wheel spacers. After a further 100 km, retighten the fastening elements of the wheels (Systems 3 and 4). For Systems 2 and 5, retighten the fastening elements of the wheels after 100 km.

Retightening Wheel Fastening Parts

Why retighten wheel fastening parts?

Settling effects in the friction pairing

After assembly, the contact surfaces of the rim, wheel hub and bolt head or nut „bed in“ under load. Surface roughness peaks are plastically deformed, and minor irregularities settle. This reduces the initial preload force in the wheel bolts or nuts. Retightening after 50–100 km restores the required preload force.

Compression of coatings and intermediate layers

Rims are often painted, powder-coated or treated with corrosion protection coatings. Centering rings or thin intermediate layers may also be present. Under wheel load and the micro-movements that occur while driving, these soft layers are compressed or partially sheared. The connection continues to „settle“, causing the contact pressure to decrease. Retightening compensates for this loss.

Effects of temperature and operating loads

While driving, changing temperatures (from braking, ambient conditions) and dynamic wheel loads act on the connection. Differing thermal expansion of the hub, rim and bolt, as well as micro-movements during driving, can further affect the preload force. Controlled retightening after the initial operating cycles ensures that, after this settling phase, the connection once again operates at the intended force level.

Safeguarding against variation during assembly

In practice, the tightening torque is always subject to a certain amount of variation (different tools, differing friction conditions, human factors). The first retightening after 50–100 km therefore also serves as an additional safety measure: it compensates for assembly and measurement inaccuracies and ensures that all wheel bolts or nuts are actually within the intended preload force range, and that the connection cannot come loose unnoticed.

When should wheel fastening parts be retightened?

After every wheel installation – for example after a tire change or the installation of wheel spacers – the connection should be checked and retightened again after a distance of around 50–100 km, as it can still change during this early operating phase due to settling and adjustment processes. Retightening is also recommended after work on the suspension or wheel hub.

For correct retightening, the vehicle should be standing on a level surface. Retightening must only be carried out using a suitable, calibrated torque wrench – an impact wrench is unsuitable, as it does not apply torque in a controlled manner. The manufacturer’s specified torque must be observed. To achieve even contact pressure on the rim, retighten in a crosswise pattern.

No lubrication may be applied to the threads or contact surfaces of wheel bolts and wheel nuts under any circumstances, as any change in friction behavior significantly affects the relationship between the applied torque and the preload force actually generated.

Bolts advice
Periodical Check
Check spacers and fixing elements at least once a year. Corroded or damaged parts must be replaced immediately.

Ball seated

Ball seated bolt
Ball Taper Radii

Tapered 60°

Tapered seat bolt

Minimum screw-in depth of fastening elements

Thread Thread reach Min. rotations
M12 x 1.25 10 mm 8.0
M12 x 1.5 10 mm 6.5
M12 x 1.75 12 mm 6.5
M14 x 1.25 12 mm 9.0
M14 x 1.5 11 mm 7.5
M14 x 2.0 14 mm 7.0
M15 x 1.25 10 mm 8.0
1/2" UNF 11 mm 8.0

Tightening torques

Consider the torque which is recommended by the vehicle and rim manufacturer for all fixing elements of spacers and wheels.
Excessive screw-in depth can lead to damage to the axles (brake parts, ABS control discs, etc.). For this reason, after fitting, the wheels should be turned by hand while still unloaded in order to check the inward clearance of the longer wheel bolts. On some vehicles, the critical tolerance is 2 mm!

Bolted Connections / Strength

Tightening Torque & Preload Force

In bolted connections – especially in safety-relevant applications such as wheel bolts/wheel nuts (hereinafter referred to as „wheel fastening parts“) – the tightening torque is not actually the target value itself. Rather, it serves as an indirect auxiliary value used to reliably build up the required preload force in the connection.

The preload force is the force that the bolt absorbs within itself as it is tightened, and which clamps the components firmly together. Only this preload force ensures that the connection can absorb forces, does not come loose, and reliably transmits shear or transverse loads.

Since the preload force can only be measured indirectly, torque is used in practice as an approximate value. However, this relationship depends heavily on the friction values at the thread and contact surface. Even small differences in lubrication, surface condition or corrosion can significantly change the preload force actually achieved – even though the same torque was applied.

The Shape of the Seat

The head shape of wheel fastening parts – typically a tapered seat or ball seat (note: different ball radii exist!) – is critical for safe force transmission between the rim and the wheel hub. The shape of the seat determines the contact area through which the wheel fastening part centers itself in the rim and evenly introduces the preload force into the contact surface. If the wrong head shape is used (e.g. tapered-seat bolts in a rim that requires a ball seat), point loads occur that can lead to material deformation, loosening of the connection, or even breakage of the wheel fastening parts or the rim. Only the head shape that correctly matches the rim ensures a form-fit and force-fit connection.

Retightening Wheel Fastening Parts

Why retighten wheel fastening parts?

Settling effects in the friction pairing

After assembly, the contact surfaces of the rim, wheel hub and bolt head or nut „bed in“ under load. Surface roughness peaks are plastically deformed, and minor irregularities settle. This reduces the initial preload force in the wheel bolts or nuts. Retightening after 50–100 km restores the required preload force.

Compression of coatings and intermediate layers

Rims are often painted, powder-coated or treated with corrosion protection coatings. Centering rings or thin intermediate layers may also be present. Under wheel load and the micro-movements that occur while driving, these soft layers are compressed or partially sheared. The connection continues to „settle“, causing the contact pressure to decrease. Retightening compensates for this loss.

Effects of temperature and operating loads

While driving, changing temperatures (from braking, ambient conditions) and dynamic wheel loads act on the connection. Differing thermal expansion of the hub, rim and bolt, as well as micro-movements during driving, can further affect the preload force. Controlled retightening after the initial operating cycles ensures that, after this settling phase, the connection once again operates at the intended force level.

Safeguarding against variation during assembly

In practice, the tightening torque is always subject to a certain amount of variation (different tools, differing friction conditions, human factors). The first retightening after 50–100 km therefore also serves as an additional safety measure: it compensates for assembly and measurement inaccuracies and ensures that all wheel bolts or nuts are actually within the intended preload force range, and that the connection cannot come loose unnoticed.

When should wheel fastening parts be retightened?

After every wheel installation – for example after a tire change or the installation of wheel spacers – the connection should be checked and retightened again after a distance of around 50–100 km, as it can still change during this early operating phase due to settling and adjustment processes. Retightening is also recommended after work on the suspension or wheel hub.

For correct retightening, the vehicle should be standing on a level surface. Retightening must only be carried out using a suitable, calibrated torque wrench – an impact wrench is unsuitable, as it does not apply torque in a controlled manner. The manufacturer’s specified torque must be observed. To achieve even contact pressure on the rim, retighten in a crosswise pattern.

No lubrication may be applied to the threads or contact surfaces of wheel bolts and wheel nuts under any circumstances, as any change in friction behavior significantly affects the relationship between the applied torque and the preload force actually generated.

Replacing Wheel Fastening Parts

Why replace wheel fastening parts?

Material fatigue

With every installation, wheel bolts and wheel nuts are subject to both elastic and, depending on friction conditions, potentially plastic stress. As the number of installation cycles increases, the components age at a material level: the surface coating wears down, the thread wears, and the friction values change. This reduces the repeatability of the tightening torque. Material fatigue is particularly critical: repeated load cycles create micro-cracks that reduce fatigue strength over the long term and, in extreme cases, can lead to failure of the connection. Regular replacement ensures that the wheel fastening always provides the necessary preload force and, with it, operational safety.

Corrosion

Corrosion significantly alters the friction conditions between the thread and the contact surface. Rust creates rougher, uneven surfaces, causing the majority of the applied tightening torque to be „lost“ to increased friction. The result: despite an identical torque, the required preload force is no longer achieved. For this reason, the condition of the wheel fastening parts must be checked regularly, and they must be replaced early at the first signs of corrosion.

Wear and Corrosion

When should wheel bolts be replaced?

Wheel bolts are exposed to strong temperature fluctuations during braking and are therefore subject to natural wear. For this reason, they must be replaced every 2 years!

If corrosion is visible, replace the wheel bolts immediately if possible.

If the wheel is changed multiple times, new wheel bolts are also required. The clamping force of the wheel bolts decreases continuously with every change!

Wheel bolts should be tightened in the correct sequence: crosswise and in several stages. If the bolts are tightened one after another in order, there will be no even contact pressure on the hub and the wheel will sit at an angle. This prevents a clean, true rotation and the wheel bolt can break.

Preventing corrosion

To prevent later wear, wheel bolts or wheel nuts should be checked for damage whenever they are changed. The bolted connections should show no rust or dirt.

Only the strength class specified by the manufacturer may ever be used – otherwise, even the smallest load can quickly lead to wear or breakage.

Product- and Vehicle-Specific Requirements
  • Not suitable for use with all vehicles or rims, as the low spacer thickness may mean the spacer does not sit flush against the hub or in the rim! Please observe the centering collar height (ZBH), hub bore depth (NLT), and chamfer values of the spacer and rim (PHO).
  • Can only be fitted to vehicles with a centering collar height (ZBH) of the vehicle hub of max. 15 mm.
  • Can only be fitted to rims with a chamfer (PHO) greater than 6 mm.
  • Please be sure to observe the enclosed mounting instructions.
  • Before installation, please check that the supplied wheel bolts match your original bolts (thread & head shape). The length of the supplied wheel bolts must be greater than that of the original bolts by approximately the thickness of the wheel spacer.
  • During installation, please check that the new or extended wheel bolts meet the minimum screw-in depth or the minimum number of thread rotations as specified in the mounting instructions.
  • During and after installation, make sure that the wheel bolts do not touch anywhere and that the wheel can turn freely.
  • Before purchasing, please check whether your vehicle, including power output range and EC number, is included in the TTG/ABE. In addition, please check whether your wheel/tyre combination is included, and observe the applicable requirements, including with regard to any possible inspection/approval.
  • Cannot be fitted in combination with steel rims.